jcr drillsol
JCR Drillsol JCR Drillsol

JCR Tractor Mounted DTH Rigs


Technical Description

Description


Mode - JCR TM 150, DTHR is a Tractor drilling rig mounted on a tractor model New Holland 7500 4WD (75HP) with Top Drive all Hydraulically Operated Drilling Rig extracting main power from Tractor Engine, is capable of drilling using DTH method to Depth of 150 Mtrs.

Capacity

a) 4 ½” (115mm) dia holes upto a depth of 150 mtrs in Rock Formation.
b) 6 ½” (165mm) dia holes upto a depth of 20 mtrs in Rock Formation.
c) 14” Dia holes upto depth of 15 Mtrs in Rock Formation.

Mast Structures
Sturdy structural mast of welded construction, main members made out of heavy duty structural steel channels reinforced with suitable cross members, with Mast length of 5500 mm, Rotary head travel of 4500mm, centralizer Opening of 254 mm i.e. (10 inches) and Raising and lowering with the help of Hydraulic Cylinder.

Top Head Rotary Drive
Heavy duty hydraulically driven top head drive with mud swivel travels on the mast constructed to with stand the drilling shock loads its speed ranges from 0-100 rpm and torque of 33,000 in-lbs. (380 kgf/m).

Feed System
Feed system is provided with adequate travel for handling drill pipes up to 3 Mtrs Long. The feed and hoist are actuated by a suitable hydraulic cylinder with wire rope and pulley arrangement. The feed system has a Pull up force of 5000 kgf i.e.(1100 Pounds), pull down force of 3000kgf i.e.(6600 Pounds, pull up speed of 15M/Min pull down speed of 34 M/Min and Reeving Ratio i.e. (wire rope) of 1:2.

The feed system will be incorporated with hold back arrangement to control and limit weight on bit, rapid and slow feed arrangement to suit the variable ground conditions.

Hydraulic System
Hydraulic System has a Capacity of Maximum Operating Pressure of 160 kg/cm2with a Hydraulic Tank Capacity of 200 Lts, Filtration (Nom) Return line of 10 microns and a Hydraulic Oil Cooler of 40GPM 2250 PSI(Fin type oil to Air).

Prime Mover
Power required for the rig Hydraulics shall be drawn from the tractor engine (75 HP) (274309) through P.T.O.

Stabilizers (Jacks)
System consists of four Hydraulics levelling jacks with reverse flow restricted valves to ensure safe operation. Two numbers are at the Rear (Operator) of the rig controlled by two separate valves and two jack in the front side of the rig controlled by a single valve.

Breakout Wrench
The Drill Rig is equipped with 350mm Stroke of 80mm Bore Hydraulically operated break out wrench for breaking drill pipes.

Water Injection Pump
The drill rig will be provided with hydraulically operated triplex Reciprocating pump of capacity 36 LPM at 400 PSI for injecting water/foam with necessary piping and flow control valve.

Air Line Lubricator
20KN Capacity main hoist with 40m/min. speed (with bare drum) with Cable of 30m length will be provided.

Wire Line winch
with 3 KN capacity with 120m/min. speed (with bare drum) with 6mm Cable dia 500 meters length will be provided.

Water Pump
The rig is provided with centrifugal pump of suitable make which is suitable for handling clear water, and bentonite solutions.

Light system
Air line lubricator capacity of 475cfm/150psi shall be mounted for the supply of lubricating oil to the hammer.
 
Sendmail
 

  Mini Tractor Category
 

JCR Tractor Mounted DTH Rigs

 

Tractor Mounted CD Rigs

   
  Our Products
 

RC Rig

DTH Water Well Rigs

Mini Drill Rigs

Refurbished Rigs

Tractor Mounted Rigs

Diamond Core Drilling Rigs

Direct Circulation Rotary Drilling Rigs

Blast Hole Drill

Pumping Testing Unit

Hydro Fractering Unit

RC Hammer & bits

DTH Hammers

Bits

Drill Pipes

Mud Pump

 
Tractor Mounted DTH Rigs
 
links drilling today